TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 59

Страница: 59 / 154

(23) Frequency Command Upper-Bound Delay Time (Bn-23)

•

The 1-8 PID Relay option card application parameter, if the AC drive’s PID output frequency

exceeds the frequency command upper bound (the Cn-14 set value), the relay output on 1-8 PID

Relay card will activate to increase the number of running pumps when the delay time set by

Bn-23 has expired.

• The set value of Bn-23 depends on the pressure response of the water supply system. The set value

should be set as low as possible to prevent mechanical shock and vibration.

(24) Frequency Command Lower-Bound Delay Time (Bn-24)

• The 1-8 PID Relay option card application parameter, if the AC drive’s PID output frequency

drops below the frequency command lower boundry (the Cn-15 set value), the relay output on

1-8 PID Relay card will activate to decrease the number of running pumps when the delay time set

by Bn-24 has expired.

• The set value of Bn-24 depends on the pressure response of water supply system. The set value

should be set as low as possible to prevent mechanical shock and vibration.

Please refer to “1-8 PID Relay Card instruction manual”.

(25) MC ON/OFF Delay Time (Bn-25)

• The1-8 PID Relay option card application parameter. Please refer to “1-8 PID Relay Card

instruction manual.”

• When switching one inverter-driven motor (or pump) to AC line power source or vice versa, set

the MC ON/OFF delay time (set value of Bn-25) to avoid the drive output and AC line source

being short-circuited due to the possible varying delay times of MC1 and MC2.

• The delay time (Bn-25 set value) must be longer than the time of the MC ON/OFF controlled

signal output from AC drive until the external MC operation is established.

•

Generally, the MC operation time from OFF to ON is longer than ON to OFF time. Therefore,

set the delay time according to the OFF to ON time.

(26) Pump ON/OFF Detection Level (Bn-26)

• The 1-8-PID Relay option card application parameter. Please refer to “1-8-PID Relay Card

instruction manual”.

• The set value of Bn-26 is the deviation level of PID set point and feedback values when

using 1-8-PID Relay option card to increase or reduce the number of running pumps.

• Set the pump ON/OFF detection level in units of 0.1%. If the value is set to 0.0%, when the output

frequency reaches the frequency upper boundry (the set value of Cn-14) the number of running

pumps increases immediately. When output frequency drops to the frequency lower boundry

(the set value of Cn-15) the number of running pumps decreases immediately.

2-9

PA 7300

PART II: OPERATION MANUAL

Inverter

MC1

MC2

AC power source

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды