TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 115

Страница: 115 / 154

29. 1-8 PID Relay Card Relay 5 Control (Sn-34)

30. 1-8 PID Relay Card Relay 6 Control (Sn-35)

31. 1-8 PID Relay Card Relay 7 Control (Sn-36)

32. 1-8 PID Relay Card Relay 8 Control (Sn-37)

• The 1-8 PID Relay option card application parameters. Please refer to “1-8 PID Relay

instruction manual”.

• Used to control the pump ON/OFF.

Sn-31 ~ 37 = 0:

Relay output invalid.

Sn-31 ~ 37 = 1:

Relay output valid.

33. Parameter Copy (Sn-38)

• The JNEP-32 LCD digital operator can upload the parameter settings from the digital operator

to the drive and download parameter settings from the AC Drive to the digital operator.

• The digital operator will check its EEPROM or the AC Drive’s EEPROM under the following settings.

Sn-38 = 0: NO action

Sn-38 = 1: Upload data (digital operator

→

AC Drive). During this period, the LED on the

digital operator will light sequentially in the CW sense.

Sn-38 = 2: Download data (AC Drive

→

digital operator). During this period, the LED on the

digital operator will light sequentially in the CCW sense.

Sn-38 = 3: Veriﬁcation check on digital operator’s EEPROM; during this period the LED

will be switched between 2 groups.

• Please follow the steps below to implement the action of parameter copy between diﬀerent

AC Drives (either upload or download).

Step 1:

Check the contents of digital operator EEPROM. (Sn-38=’03’), then check the

contents of AC Drive’s EEPROM. Make sure that both EEPROM function properly.

Step 2:

Download and copy the AC Drive’s parameter settings to digital operator

EEPROM (Sn-38=2).

Step 3:

Upload and copy the parameter settings of digital operator to other AC Drive’s

EEPROM (Sn-38=1)

Note:

When transferring preameters from one drive to another, the following

restrictions apply

a) Parameter transfer is only allowed between identical model numbered units.

b) Parameter transfer should be performed with units at the same software

revision levels. Otherwise consult the factory for compatibility.

2-65

PA 7300

PART II: OPERATION MANUAL

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды