TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 32

Страница: 32 / 154

• CHARACTERISTICS

Control Method

Sine wave PWM

Frequency Control Range

0.1 to 180Hz

Frequency Accuracy

Digital command: 0.01% -10 to 40˚C\ +14 to 104˚F

Analog command: 0.1% 25 ± 10˚C\77 ± 18˚F

Frequency Setting Resolution

Digital operator reference: 0.01Hz,

Analog reference: 0.06Hz/60Hz

Output Frequency Resolution

0.01Hz (1/30000)

Overload Capacity

110% rated output current for one minute.

Frequency Setting Signal

0 to 10VDC (20KΩ), 4~20mA (250Ω), 0 ~ ± 10 VDC (option)

Accel/Decel time

0.1 to 6000 sec (independent Accel/Decel time settings)

Braking Torque

Approximately 20%

Type of. V/Hz patterns

(Total of 5)

1: For adjustable pattern.

4: For fans and pumps.

Motor Overload Protection

Electric thermal overload relay

Instantaneous Overcurrent

Motor coasts to stop at approx. 200% rated current.

Overload

Motor coasts to stop after 1 minute at 110% rated output current.

Overvoltage (230V class)

Motor coasts to stop if AC Drive output voltage exceeds 410VDC.

Overvoltage (460V class)

Motor coasts to stop if AC Drive output voltage exceeds 820VDC.

Overvoltage (600V class)

Motor coasts to stop if AC Drive output voltage exceeds 1050VDC

Undervoltage (230V class)

Motor coasts to stop if AC Drive output voltage drops to 190VDC or below.

Undervoltage (460V class)

Motor coasts to stop if AC Drive output voltage drops to 380VDC or below.

Undervoltage (600V class)

Motor coasts to stop if AC Drive output voltage drops to 546VDC or below

Momentary Power Loss

Motor coasts to stop after momentary power loss lasting over 15ms.

(time-setting made before shipment).

Motor Overheat Protection

Motor PTC thermistor (Active: 1330Ω, Return: 550Ω)

Input Phase Loss

Single phase protection.

Output Phase Loss

Provided by electronic circuit.

Fin Overheat

Thermostat

Stall Prevention

Stall prevention at acceleration/deceleration and constant speed operation.

Ground Fault

Provided by electronic circuit.

Power Charge Indication

Charge lamp stays ON until bus voltage drops below 50V.

Location

Indoor (Protected from corrosive gases and dust)

Ambient Temperature

Wall-mounted type: +14 to 104˚F (-10 to +40˚C ),(not frozen)

Open chassis type: +14 to 113˚F ( -10 to +45˚C ), (not frozen)

Storage Temperature

-4 to 140˚F (-20 to +60 ) °C

Humidity

95% RH (non-condensing)

Vibration

1G at 10 to 20Hz, up to 0.2G at 20 to 50Hz.

Communication Protocols

RS-485 MODBUS, PROFIBUS (option), METASYS (option), LONWORKS (option)

Noise Interference Suppression

EN 61800-3 (2000) with speciﬁed noise ﬁlter

Noise Immunity

EN61800-3 (2000)

7-3

PA 7300

PART I: INSTALLATION MANUAL

ol Char

teristics

tiv

e F

unc

tions

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды