TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 135

Страница: 135 / 154

c. How to adjust

The PID control function is a control system that matches a feedback value to the set point.

Combining P (Proportional, Bn-14), I (Integral, Bn-15), and D (Derivative, Bn-16) makes control

possible even for a mechanical system with dead time. The PID control function, using diﬀerent

detected sensors, can be used for speed, pressure, ﬂow, or temperature etc. applications.

(1) PID control operations.

In order to distinguish the separate PID control operations. The ﬁgure below shown the

changes in the control input when the deviation between the target set point and the feed

back is held constant.

Fig. 14 PID Control Operations

• P Control:

A control input proportional to the deviation is asserted. The deviation cannot

be zeroed by P control alone.

• I Control:

A control input which is an integral of the deviation is asserted. This is eﬀective

for matching the feedback to the target value. Sudden changes, however,

cannot be followed.

• D Control:

A control input which is an integral of the deviation is asserted. Quick response

to sudded changes is possible.

• PID Control:

Optimum control is achieved by combining the best features of P, I,

and D control.

App-5

PA 7300

APPENDIX

Deviation

Control input

Time

PID control

I control

P control

D control

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды