manualshive.com logo in svg

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 124

The warning and self-diagnosis functions do not operate fault contact outputs (except OH1  
warning function) and return to the former operation status automatically when the condition is 
removed. The fault display and troubleshooting are provided as shown in the table below.

  FAULT CONTACT
 

OUTPUT 

ERROR CAUSES 

ACTION TO BE TAKEN

 

 

•  AC Drive capacity is too small.

 

 

•  Voltage drop due to wiring.

 

 

•  AC Drive power voltage selection is wrong

 

 

•  A motor of large capacity (11 kW or greater) connected 

•  Check the power capacity and power system.

 

 

  to the same power system has been started. 

•  UV display appears when the AC Drive power is

 

Operation 

•  Rapid acceleration with generator power supply 

  turned off while operation signal is inputed. Remove

 

 

•  Operation sequence when power is off 

  the power after stopping the AC Drive.

 

 

•  Defective electromagnetic contactor 

•  (Set the third and fourth bits of Sn-04 to 01.)

 

 

•  Extremely rapid accel/decel

 

 

•  Motor on/off switching at the AC Drive output side

 

 

•  Short-circuit or ground-fault at the AC Drive output side 

Transistor error may occur. Investigate the error

 

Operation 

•  Motor of a capacity greater than the AC Drive rating has 

cause, correct it, then restart.

 

 

  been started

 

 

•  High-speed motor or pulse motor has been started.

 

 

•  Motor dielectric strength is insufficient.

 

Operation 

•  Load wiring is not proper. 

Check for ground-fault in motor or load wiring.

 

 

•  Over voltage

 

 

•  Insufficient deceleration time 

If required braking torque is excessive, extend the decel time

 

Operation 

•  Regenerative load (Motor is turned by the load.) 

or use a braking resistor. (If braking resistor is already

 

 

•  High input voltage compared to motor rated voltage 

installed, verify that Sn-10. 2nd digit to 1.)

 

 

•  Defective cooling fan.   

Replace the cooling fan and clean the filter.

 

 

•  Ambient temperature rise 

Ambient temperature:

 

Operation 

•  Clogged filter 

 

104 °F (40 °C) or less for enclosed type

 

 

   

 

122 °F (45 °C) or less for open chassis

 

 

   

 

Investigate the cause of overload and review the

 

 

   

 

operation pattern, V/f characteristic, and motor/AC Drive

 

Operation 

Overload, low speed operation, or extended acceleration 

capacities. (If AC Drive is repeatedly reset after an

 

 

time, improper V/f characteristic setting 

overload occurs, the AC Drive may fault. Investigate

 

 

   

 

and correct the cause of overload.)

 

Operation 

Motor current exceeds the preset value because of 

Check the use of the machine. Correct the overload

 

 

machine error or overload. 

cause or set a higher detection level which is within

 

 

   

 

the allowable range.

 

Operation 

External fault condition occurred 

Correct the source of the fault input.

 

Operation 

•  External noise 

 

Check data in Sn-01 and Sn-02. Record all data, then

 

 

•  Excess vibration or shock 

use Sn-03 for initializing.

 

 

•  CPF 02:  

Control circuit fault 

Cycle power. If error is persistant,

 

 

•  CPF 03:  

NVRAM (SRAM) fault 

contact your TECO representative

 

 

•  CPF 04:  

NVRAM BCC Code error

 

 

•  CPF 05:  

AD converter fault in CPU

3-2

 

PA 7300

 

PART II: OPERATION MANUAL

Содержание PA7300 Series



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды