TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 22

Страница: 22 / 154

4.4.2 CAUTIONS FOR WIRING

(A) MAIN CIRCUIT INPUT/OUTPUT

(1) Phase rotation of input terminals L1 (R), L2 (S), L3 (T) is available in either direction.

(Clockwise and counterclockwise).

(2) When AC Drive output terminals T1 (U), T2 (V), and T3 (W) are connected to motor terminals

T1(U), T2 (V), and T3 (W), respectively, the motor rotates counterclockwise. (Viewed from opposite

side of drive end, upon forward operation command). To reverse the rotation interchange any

two of the motor leads.

(3) Never connect the AC main circuit power supply to output terminals T1 (U), T2 (V), and T3 (W).

This may cause damage to the AC Drive.

(4) Care should be taken to prevent contact of wiring leads with the PA7300 cabinet. If this occurs, a

short-circuit may result.

(5) Never connect power factor correction capacitors or noise ﬁlters to the PA7300 output.

(6) Never open or close contactors in the output circuit unless AC Drive is properly sized.

(7) The main circuit wiring should use suitable O-type terminals, and the width of each terminal must

be less than the terminal block to insure that each terminal is isolated.

CAUTION

The external interconnection wiring must be performed with the following procedures.

After completing PA7300 interconnections, be sure to check that connections are

correct. Never use control circuit buzzer check.

CAUTION

• Lead size should be determined by taking into account voltage drops of leads. Voltage drops can

be obtained by the following equation: select lead size such that voltage drop will be within 2% of

the normal rated voltage.

Phase-to-phase voltage drop (V):

=√3 x lead resistance ( Ω /km) X wiring distance(m) x current(A) X 10

-3

• Wiring length between AC Drive and motor:

If total wiring distance between AC Drive and motor is excessively long and AC Drive carrier

frequency (main transistor switching frequency) is high, harmonic leakage current from the cable

could aﬀect the inverter unit or peripheral devices. If the wiring distance between inverter and

motor is long, reduce the AC Drive carrier frequency.

4-8

PA 7300

PART I: INSTALLATION MANUAL

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды