TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 132

Страница: 132 / 154

App-2

PA 7300

APPENDIX

b. Energy-Savings operation procedures

(1) Enter the Energy-savings mode by setting the third digit of the operation mode selection

5 (Sn-09) to 1. (The Energy-savings mode is already set prior to shipping.)

(2) Set Cn-60 to the motor code (refer to page App-1) which is determined by the

motor capacity and voltage.

(3) Set operation frequency.

(4) Input the run command. The motor accelerates up to the set frequency (bn-01). When

it reaches the set value, the Energy-savings mode is enabled and operations perform at

voltages according to the load.

c. Veriﬁcation of Energy-savings Power

Energy-savings power can vary by comparing power in the V/f control mode operation

(Sn-09 third digit to 0) with power in the Energy-savings mode operation (Sn-08 third digit to 1).

Power can be monitored by Un-06.

Energy savings values vary according to the load ratio. Little energy-savings eﬀect is realized

with load ratios exceeding 70%. As the load becomes lighter, the eﬀect becomes greater.

d. Adjustment

Since the constants used in the Energy-savings mode are already set initially to the optimum

values, adjustments are not normally needed. However, when the motor characteristics are much

diﬀerent from those of the TECO standard motors, or if a fault occurs because of improper constant

setting, then perform the following adjustment.

Adjustment at fault Occurrence

FAULT

CORRECTIVE ACTION

Power does not change in the Energy-savings mode.

Does setting frequency exceed 100Hz? If it does,

the Energy-savings mode is released.

Power variation is very small in the Energy-savings mode.

Is the load ratio excessively large? When the load ratio is

excessively large, energy saved value becomes larger as the

load becomes lighter.

Hunting at a light load

Increase the time constant (On-16) of power detecting ﬁlter

Current increases to cause OL1 or OL2 although within

Decrease the value (Cn-46) of Energy-savings voltage upper

rated load torque (Especially at low frequency)

limit at 6Hz. Or decrease the energysaving coeﬃcient

reduction ratio (Cn-59)

When the Energy-savings mode is entered after completion

Increase the lower (Cn-47 or Cn-48)

  of acceleration, the motor stalls to a stop (especially
  at a light load).
  Revolutions change periodically and its cycle is almost

Decrease search operation voltage stop (Cn-51 or Cn-52)

equal to Cn-50 set value.

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды