TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 138

Страница: 138 / 154

C. RS-485 COMMUNICATION CONNECTION DIAGRAM

The PA7300 provide PA-C (METASYS/MODBUS protocol) and PA-P (PROFIBUS-DP protocol) option card

for RS-485 communication interface. The wiring diagrams of PA-C and PA-P are as below.

(a) PA-C METASYS/MODBUS protocol communication

The PA-C option card supports the METASYS/MODBUS protocol can be placed at the upper side

of the control board.

Fig. 15 Wiring for PA-C METASYS/MODBUS Protocol communication

Note: 1.

A Host Controller with RS-485 interface can communicate with the PA7300 unit through the

PA-C option card. If the Host Controller does not provide the RS-485 port and its RS-232 port

is available, an RS-485/RS-232 conversion card should be used to connect between this

Host Controller and PA-C option card of PA7300.

A METASYS/MODBUS Host Controller can drive the network with no more than 31 drivers

connected, using MODBUS communication standard. If the driver (e.g., PA7300 drive) is at the

end of the network it must have the terminating resistors 220Ω at both terminals (By SW1

dip Switch). All other drives in the system should not have their terminating resistor active.

The PA-C cards with RS-485 and RS-422 interface can be selected by TP1 jumper.

Please refer to the “PA7300 PA-C RS-485 METASYS/MODBUS Communication Application Manual”.

App-8

PA 7300

APPENDIX

RS-485

interface

RS-485

Controller

220

(Terminator

Resistor)

PA7300

M31

(PA-C)

TB1

S+

S-

shield

SW1

TP1

RS-485

PA7300

(PA-C)

TB1

S+

S-

shield

TP1

RS-485

PA7300

(PA-C)

TB1

S+

S-

shield

TP1

RS-485

–

RS-232

Controller

DATA(+)

DATA(-) Rx

RS-485/RS-232

adaptor

RS-232

interface

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды