TECO-Westinghouse PA7300 Series Скачать руководство пользователя страница 94

Страница: 94 / 154

•

3rd digit

(operation continued at momentary power loss)

3rd digit = 0:

When momentary power loss is detected, under-voltage fault (UV1) occurs

and the AC drive output is shut oﬀ.

3rd digit = 1:

If momentary power loss time is within momentary power loss ride-thru

time (Cn-37), the operation continues after the momentary power loss. If the

momentary power loss ride-thru time is exceeded, under-voltage fault (UV1)

occurs and the AC drive output is shut OFF.

Notes:

1. When the 3rd digit = 1, do not shut OFF the external sequence signal (e.g. FWD, REV)

2. For lifters, do not use this function (set 3rd digit = 0)

•

4th digit

(Not used)

(12) Protective Characteristics Select 3 (Sn-12)

When an external fault signal of terminal 3 is asserted, “Ext. Fault 3 EF3” is displayed and a fault

contact signal is immediately generated. The AC drive stops according to the setting of the 3rd and

4th digits. The external fault signal is held within the AC drive until a fault reset signal is input.

• 1st digit

(level selection of the external fault signal)

1st digit = 0:

NO-contact input (when “closed”, the external fault operation is performed)

1st digit = 1:

NC-contact input (when “open”, the external fault operation is performed)

•

2nd digit

(acceptance of the external fault signal)

2nd digit = 0:

External fault signals are always accepted.

2nd digit = 1:

External fault signals are accepted only during run. (Not accepted

during baseblock)

•

3rd digit, 4th digit

(selection of processing at external fault detection)

3rd digit

4th digit

Contents

Ramp stop by Bn-02 (major fault).

Coast to stop (major fault)

Ramp stop by Bn-04 (major fault).

Operation to continue (minor fault).

(13) Protective Characteristics Selection 4 (Sn-13)

•

1st digit

(Input Phase Loss Protection, IPL)

The input phase loss protection, function is disabled when input phase loss detection

level Cn-61=100%. The eﬀectiveness or ineﬀectiveness of input phase loss protection

function can also be selected by the 1st digit of Sn-13.

2-44

PA 7300

PART II: OPERATION MANUAL

Содержание PA7300 Series



























































































































































Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO-Westinghouse PA7300 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PA7300 Series

Отзывы:

Бренды по названию

Популярные бренды