manualshive.com logo in svg

Takeuchi TB175, Руководство оператора, Страница: 99 / 231

Поделиться
Скачать
Takeuchi TB175 Скачать руководство пользователя страница 99

96

MAINTENANCE

General

Cautions on Maintenance

Do not perform inspection and maintenance
procedures not prescribed in this manual.
Have inspection and maintenance
procedures not prescribed in this manual
performed by a Takeuchi sales or service
outlet.

Always keep the machine clean.

¡

Always keep the machine clean, and wash
it before performing inspection and
maintenance.

¡

When washing the machine with water,
stop the engine and cover the electrical
system with plastic to protect it from water.
Exposing the electrical system to water is
dangerous and could result in short-
circuits or malfunction. Do not wash the
battery, sensors, connectors or the inside
of the cab with water or steam.

Fuel, lubricant and grease

¡

For fuels, lubricant and grease, follow the
instructions on the “Fuel and Lubricant
Chart”.

¡

Use pure fuels, lubricants and greases
which do not contain water, and be careful
to keep dirt out when changing or
replenishing fuel, lubricant or grease.

¡

Store fuels, lubricants and greases in the
prescribed places and in such a way that
no water or dirt can get in them.

Cautions on fueling

¡

If the port includes a strainer, do not
remove the strainer when fueling.

¡

After fueling, be sure to securely tighten
the cap, etc.

¡

Do not add more than the prescribed
amount of fuel.

Maintenance Description

For long-term use of the machine under good
conditions, perform the inspection and
maintenance procedures properly and safely
as recommended in this manual.

The inspection and maintenance items are
divided according to the machine’s total
operating time (inspection and maintenance
to be performed every 10 hours (walk-around
and daily inspection), every 50 hours, every
250 hours, etc.). Refer to the hour meter to
determine when it is time to perform
inspection and maintenance. Items for which
it is not possible to determine the inspection
and maintenance interval are included under
“When Required”.

When operating the machine in extremely
harsh environments (with high dust levels or
high temperatures), inspection and
maintenance should be performed earlier
than the times indicated on the Maintenance
Chart.

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов