Takeuchi TB175 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 231

Takeuchi TB175 Скачать руководство пользователя страница 63

60

CONTROLS

Accessories

(4) Program indicators
Indicates tape direction. When

s

lamp is on.

Upper side of a tape is playback,

t

indicates

playback of lower side.

(5) Display

(A) Band
(B) Time/Frequency
(C) Memory channel(1–6)
(D) Metal
(E) FM Stereo
(F) Loudness
(G) Tape direction

(6) Eject button
Push this button to eject the cassette tape.

¡

To change over to radio while listening to
a cassette tape, press the EJECT button
to stop the tape and the system will
automatically change over to radio.

(7) Cassette door
Insert the cassette tape with the exposed
magnetic tape side facing to the right.

¡

Simply insert a tape to change over to the
cassette tape mode while listening to the
radio.

(8) Fast-forward / rewind / program

changeover button

Fast-forward

Fast-rewind / Stop

To fast-forward the tape, push the button
matching the direction of program indication
and to rewind, push the other button. To stop
fast-forwarding or rewinding, lightly press the
button which is not locked to cancel the
operation. The system will then start playing
the tape again normally.

MTL LOUD ST

FM1
FM2
AM

L2C002

G

A

C

D F

B

E G

MTL LOUD ST

FM1
FM2
AM

L2C003

MTL LOUD ST

FM1
FM2
AM

L2C004

«
...
61
62
63
64
65
...
»

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов