Takeuchi TB175 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 231

Takeuchi TB175 Скачать руководство пользователя страница 73

70

OPERATION

Machine Operation

Warming Up the Machine
(Hydraulic Oil)

WARNING

Operating the working equipment without
warming up the machine (hydraulic oil)
is dangerous, as response will be slow
and the equipment may move in
unexpected ways and safety devices may
not operate properly. Be sure to
sufficiently warm up the machine.

IMPORTANT: Do not operate the levers
suddenly when the hydraulic oil
temperature is below 20

°

C (68

°

F). The

proper hydraulic oil temperature during
operation is 50 to 80

°

C (122 to 176

°

F), but

if operations must be performed at lower
temperatures, heat up the hydraulic oil
to at least 20

°

C (68

°

F).

Normal Warm-up

1. Run the engine at medium speed (FC

mode) for about 5 minutes with no load.

2. Fully lower the safety lock lever to

disengage the lock and lift the bucket from
the ground.

3. Extend and retract each of the cylinders

several times with no load.

4. Slew slowly left and right several times.

L

H

L3D008

FC

L3D009

G4D005

«
...
71
72
73
74
75
...
»

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов