manualshive.com logo in svg

Takeuchi TB175, Руководство оператора, Страница: 102 / 231

Поделиться
Скачать
Takeuchi TB175 Скачать руководство пользователя страница 102

99

MAINTENANCE

Expendables

Replace expendables such as filters and elements periodically, referring to the table below.

Service Data

Item

Part name

Part No.

Replacement interval

Hydraulic oil return
filter

Element

After first 50 hrs.
Every 500 hrs.

15511-02600

Fuel filter

Every 500 hrs.

Cartridge

119802-55800

After first 50 hrs.
Every 250 hrs.

129150-35152

Engine oil filter

Cartridge

Every 1000 hrs. or
after 6 cleanings
(whichever comes
first)

Air cleaner

Outer Element

129062-12560

Air breather filter

Every 1000 hrs.

Element

15520-00902

Water separator filter

Cartridge

129901-55850

Every 1000 hrs. or
after 3 cleanings of
the outer element
(whichever comes
first)

Inner Element

119005-12571

Replace the hydraulic oil regularly!

Replacement Interval (Hours)

Item

Hydraulic Oil Filter Element

1st time

25

2nd time

100

Periodically

600

200

When the breaker operating ratio is 100%
Refer to page 193 “Hydraulic Breaker”.

When using a hydraulic breaker, the oil
deteriorates quicker than during normal
digging. Be sure to replace the hydraulic oil
and return filter element.

¡

Failure to replace these in time can lead
to damage to the machine and breaker’s
hydraulic systems. In order to improve the
service life of the hydraulic systems, be
sure to replace the hydraulic oil and return
filter element according to the following
chart of the replacement interval.

¡

Clean the suction strainer when changing
the return filter element.

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов