Takeuchi TB175 Скачать руководство пользователя страница 86

Страница: 86 / 231

OPERATION

Operating Procedures

Getting Out of Mud

If the machine gets stuck in mud, use the
procedure below to get it out.

If one crawler is stuck

1. Slew the bucket to the side which is stuck.
2. Set the arm and boom to an angle of 90

to 110

3. Press the bottom of the bucket (not the

teeth) against the ground.

4. Place a plank, etc., under the lifted crawler.
5. Lift the bucket and slowly move out of the

mud.

If both crawlers are stuck
1. Perform steps 1 to 4 above for both

crawlers.

2. Dig the bucket into the ground in front of

the machine.

3. Pull with the arm and travel forward

simultaneously to slowly move out of the
mud.

Do not open the door while traveling on
slopes

Opening the door while traveling on slopes
is dangerous, as the force required to open
and close the door changes abruptly. Always
keep the door closed when traveling on
slopes.

E4D048

Содержание TB175








































































































































































































































Результаты поиска

Содержание TB175

Отзывы:

Takeuchi TB175, Руководство оператора, Страница: 86 / 231

Результаты поиска

Содержание TB175

Отзывы: