manualshive.com logo in svg

Takeuchi TB175, Руководство оператора, Страница: 208 / 231

Поделиться
Скачать
Takeuchi TB175 Скачать руководство пользователя страница 208

205

OPTIONS

Second / Fourth Auxiliary
Hydraulic Switches

Slider switch (Proportional control) and
Buttons

Move or press those switches to control the
flow of the oil in the fourth auxiliary hydraulic
lines.

(G) ..... Hydraulic oil flows to left auxiliary

line(g)

(H) ..... Hydraulic oil flows to right auxiliary

line(h)

¡

When the safety lock lever is set to the
lock position, this control is locked.

Disconnecting the hydraulic circuits
1. Release the pressure remaining in the

lines.
When equipped with accumulator :
Refer to page 199 “Releasing the residual
pressure”.

2. Disconnect the lines from ports (g) and

(h).

3. Install the plugs.

Fourth Auxiliary Hydraulics

Selector Button (2-Piece boom)

 WARNING

Pressing (switching ON or OFF) the
selector button while the boom swing
pedal is depressed is dangerous, since
the attachment will move unexpectedly.
Always set the boom swing pedal back
to the neutral position before operating
the selector button.

This button changes from the boom swing
operation to the intermediate boom
operation.
Press this button to change over to operation
of the intermediate boom . The intermediate
boom operation indicator lamp will light. One
more press of this button will result in a return
to boom swing operation. Actual operation
is performed with the boom swing pedal.
Operation of the first auxiliary hydraulic
switch push button: left side (A) only.

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов