Takeuchi TB175 Скачать руководство пользователя страница 190 | Manualshive

Страница: 190 / 231

Takeuchi TB175 Скачать руководство пользователя страница 190

OPTIONS

187

Switching the Lever Pattern

The operating pattern of the left and right operating levers can be changed.

WARNING

Before starting the engine, check the selector to see which operating pattern the left
and right operating levers are set for.

Switching the Lever Pattern

1. Park the machine in a safe place and turn

off the engine.

2. Fully open the cab door and fix it in place.
3. Lift up the floor mat at the cab entrance.
4. Open the cover (1).
5. Loosen the wing bolt (2).
6. Turn the selector valve lever (3) and switch

the pattern.

7. Tighten the wing bolt (2) and fasten the

lever (3) in place.

8. Close the cover (1) and set the floor mat

back in place.

9. Check the lever pattern.

(A) : ISO pattern
(G) : JCB pattern

ISO

A

JCB

G

C4L004

L3L0021

2

3

G

A

1

«
...
188
189
190
191
192
...
»

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов