Takeuchi TB175 Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 231

Takeuchi TB175 Скачать руководство пользователя страница 151

148

TROUBLESHOOTING

If a Warning Lamp Flashes

If an alarm is sounded or a warning lamp starts flashing during operation, park the machine
in a safe place and perform the procedures described below.

Warning lamp

Lamp name

Procedure

The coolant temperature has risen irregularly and the
engine is overheating.
Refer to page 143 “If the Engine Overheats”.

Engine
emergency
lamp

A problem has occurred in the engine lubrication system
or cooling system.

¡

When there is a problem in the engine lubrication
system or coolant level, the engine oil pressure/coolant
level warning lamp flashes simultaneously.

¡

When the coolant water temperature has risen
irregularly, the coolant temperature warning lamp
flashes simultaneously.

For the procedures, refer to the respective warning
lamps below.

Battery charge
warning lamp

There is a problem with the fan belt or charger.
Inspect the fan belt for slack or breakage and adjust as
necessary. If the lamp continues flashing after
maintenance, there is a problem with the charger.
Consult a Takeuchi sales or service outlet.
Refer to page 114 “Inspecting and Adjusting the Fan
Belt”.

Engine oil
pressure/
coolant level
warning lamp

Inspect the engine oil level or coolant level. If the lamp
is flashing even though the level is normal or if it
continues flashing after oil or coolant are supplied,
consult a Takeuchi sales or service outlet.
Refer to page 107 or 108 “Inspecting and replenishing
the coolant” or “Inspecting and Replenishing the
Engine Oil”.

Coolant
temperature
warning lamp

OSOB080

Air cleaner
warning lamp

The air cleaner filter is clogged.
Refer to page 120 “Cleaning the Air Cleaner”.

C4B012

G4B009

C

G4B010

L3J004

«
...
149
150
151
152
153
...
»

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов