Takeuchi TB175 Скачать руководство пользователя страница 125

Страница: 125 / 231

122

MAINTENANCE

Replacing the Fuel Filter

WARNING

Do not smoke or permit open flames
while handling fuel or working on the
fuel system.

Stop the engine in a well-ventilated
place and allow it to cool down before
performing maintenance.

Clean up spilled fuel immediately.

1. Open the right side cover.
2. Using a filter wrench, turn the filter (1)

counterclockwise and remove it.

3. Clean the surface of installation of the filter

stand.

4. Apply a thin layer of oil to the packing of

the new filter.

5. Install the new filter by hand.
6. Tighten 2/3 more turn with the filter wrench

after the filter packing comes in contact
with the surface of installation.

7. Bleed the air.

Refer to page 145 “Bleeding the Air from
the Fuel System”.

Replacing the Hydraulic Oil
Return Filter

Refer to page 112 “Replacing the Hydraulic
Oil Return Filter”.

Every 500 Hours

L3G031

Содержание TB175








































































































































































































































Результаты поиска

Содержание TB175

Отзывы:

Takeuchi TB175, Руководство оператора, Страница: 125 / 231

Результаты поиска

Содержание TB175

Отзывы: