manualshive.com logo in svg

Takeuchi TB175, Руководство оператора, Страница: 142 / 231

Поделиться
Скачать
Takeuchi TB175 Скачать руководство пользователя страница 142

139

MAINTENANCE

When Required

Installation
1. Engage the crawlers with the left and right

sprockets.

2. Set the left and right crawlers on the idlers.
3. Start the engine.
4. Press the travel speed switch once and

set it to the 2nd speed side. The left and
right crawlers are tightened
simultaneously.

5. Check that the crawlers are properly

tightened. Standard value (A).
Refer to page 115 “Inspecting the Crawler
Tension”.

9. Slowly lower the dozer blade side of the

machine body, by the dozer blade lever.
(Do not start the engine.)

10. Ground the crawlers and lower the

machine body so that the crawler slack
is maximum.

11. When the crawlers come away from the

idlers, slide the crawlers to the outside
and remove them.

12. Disengage the crawlers and sprockets,

then remove the crawlers from the
crawler frames.

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов