Takeuchi TB175 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 231

Takeuchi TB175 Скачать руководство пользователя страница 129

126

MAINTENANCE

Every 1000 Hours

Inspecting and Adjusting the
Engine Valve Clearance

This operation requires experience. Have it
performed by a Takeuchi sales or service
outlet.

Retightening the Engine Cylinder
Head Bolts

This operation requires experience. Have it
performed by a Takeuchi sales or service
outlet.

Inspecting the Engine Fuel
Injection Pressure and Spray
Condition

This operation requires experience. Have it
performed by a Takeuchi sales or service
outlet.

Replacing the Travel Motor Gear
Oil

Refer to page 119 “Replacing the Travel
Motor Gear Oil”.

Replacing the Air Breather Filter

WARNING

¡

¡

¡

¡

¡

Never jump off the machine. Use the
steps and handrails when climbing on
and off the machine, and always
support your body at three points with
your hands and feet.

¡

¡

¡

¡

¡

Oil may spurt out if caps or filters are
removed or pipes disconnected before
releasing the pressure in the hydraulic
system.
• Gradually press the air breather

button to relieve tank pressure.

1. Remove cap nut (N) on the air breather.
2. Press botton (T) and bleed the air from

the tank.

3. Remove seal washers (W) and nut (G).
4. Remove cover (H).
5. Replace filter (A), making sure it is in the

proper direction.

6. Line up the cut section of body (B) and

cover (H) and install.

7. Install seal washers (W) and nut (G).
8. Tighten securely by hand with cap nut (N).

N

W

G

W

H

A

T

B

L2G023

«
...
127
128
129
130
131
...
»

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов