manualshive.com logo in svg

Takeuchi TB175, Руководство оператора, Страница: 211 / 231

Поделиться
Скачать
Takeuchi TB175 Скачать руководство пользователя страница 211

208

OPTIONS

Air Conditioner

Air Conditioner Switch

IMPORTANT: To  avoid placing an
excessive load on the compressor, wait
until the engine is started and is running
smoothly before turning on the air
conditioner.

Use this switch to turn the air conditioner ON
and OFF.  When this switch is pressed while
the engine is running and the fan switch is
ON, the air conditioner turns on.  Press the
switch again or turn the fan switch OFF to
stop the air conditioner.
O ...... OFF
 I ....... ON
Supplement: To prevent leakage of coolant
gas from the compressor’s seal, operate the
air conditioner at least once a week,
regardless of the season.
Supplement: The air conditioner will not
function if the temperature in the cab is low
(about 3

°

C (38

°

F) or lower).

Temperature Control Dial

Use this dial to adjust the air temperature.
COOL ..... To lower the temperature
WARM .... To increase the temperature
Supplement: No warm air is emitted if the
temperature of the engine coolant is low.

Fan Switch

Use this switch to adjust the fan speed in
three steps. At the OFF position, the air
conditioner is also OFF.
OFF ........ Fan and air conditioner off

............. Low
............. Medium

............ High

L3T006

L3T005

COOL

WARM

L3T003

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов