manualshive.com logo in svg

Takeuchi TB175, Руководство оператора, Страница: 213 / 231

Поделиться
Скачать
Takeuchi TB175 Скачать руководство пользователя страница 213

210

OPTIONS

Air Conditioner

After starting the engine, turn the air
conditioner ON and adjust the switches as
shown in the diagram above.
Set the temperature control dial and fan
switch to the desired positions.

Quick cooling

To cool the cab quickly, set the airflow mode
control dial to the recirculation position and
the fan switch to High, as shown on the
diagram above.

Defogging the Windows

 CAUTION

If the air conditioner is set to high when
using the defroster, the difference
between the external and internal
temperatures increases, and fog may
form on the outside of the windows.  If
this happens, either turn the air
conditioner OFF or turn the temperature
control dial clockwise (WARM).

After starting the engine, turn the air
conditioner ON and adjust the switches as
shown in the diagram above.
The outflow slot of foot area and the outflow
slots of the defroster can be directed at the
front window.

L3T009

L3T010

L3T009

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов