Takeuchi TB175 Скачать руководство пользователя страница 85

Страница: 85 / 231

OPERATION

Operating Procedures

Braking when traveling down slopes

When traveling down slopes, the brakes are
applied automatically when the travel levers
are returned to the neutral position.

If the crawlers slip

If the crawlers slip while traveling up a slope,
use the pulling force of the arm to climb the
slope.

If the engine stops

If the engine stops when traveling down a
slope, set the travel levers to the neutral
position, stop the machine, then start the
engine.

Traveling Posture
Traveling up slopes

When traveling up slopes at an angle of 15

or greater, travel in the posture shown in the
diagram above.

Traveling down slopes

When traveling down slopes at an angle of
15

or greater, lower the engine speed and

travel in the posture shown in the diagram
above.

Climbing

E4D045E

Braking

E4D046

Descending

E4D047E

Содержание TB175








































































































































































































































Результаты поиска

Содержание TB175

Отзывы:

Takeuchi TB175, Руководство оператора, Страница: 85 / 231

Результаты поиска

Содержание TB175

Отзывы: