Takeuchi TB175 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 231

Takeuchi TB175 Скачать руководство пользователя страница 105

102

MAINTENANCE

Important Parts

For safe use, the machine must be serviced periodically. To increase safety, periodically
replace the parts listed in the following table of important parts.
Serious injury or a fire could result if they deteriorate or are damaged.

Table of Important Parts

Above important parts are vulnerable to aging and wear or deterioration and it is difficult to
determine the degree to which they have deteriorated on the occasion of periodic service. To
maintain their proper function at all times, therefore, replace them with new ones after using
them for a specific period of time even if no abnormality is found with the parts. If you find
abnormalities in these parts before their scheduled replacement time is reached, repair or
replace them immediately. If a hose clamp is deformed or cracked, replace it immediately.
When replacing the important parts, please contact a Takeuchi sales or service outlet.

Also check the hydraulic hoses other than the above important parts. If any abnormality is
found in them, retighten them or replace them immediately.
When replacing the hydraulic hoses, replace the O-rings and seals at the same time.

Check the fuel and hydraulic hoses according to the periodic schedule described below.
Refer to “Maintenance”.

Type of inspection

Inspection item

Daily inspection

Leakages from joints, hydraulic or fuel hoses.

Monthly inspection Leakages from joints, hydraulic or fuel hoses.

Damaged hydraulic or fuel hoses(cracks, wear and tear).

Annual inspection Leakages from joints, hydraulic or fuel hoses.

Deteriorated, twisted, damaged hydraulic or fuel hoses (cracks, wear
and tear) or hoses in contact with other parts of the machine.

Unit

Important parts to be replaced periodically

Replacement Interval

Fuel hoses
Packing in fuel filler cap
Engine oil filter hoses
Heater hoses
Air conditioner hoses
Hydraulic hoses ( Pump - delivery )
Hydraulic hoses ( Pump - suction )
Hydraulic hoses ( Slew motor )
Hydraulic hoses ( Travel motor )
Hydraulic hoses ( Boom cylinder lines )
Hydraulic hoses ( Boom adjustment cylinder lines )
Hydraulic hoses ( Arm cylinder lines)
Hydraulic hoses ( Bucket cylinder lines )
Hydraulic hoses ( Swing cylinder )
Hydraulic hoses ( Blade cylinder )
Hydraulic hoses ( Tension cylinder )
Hydraulic hoses ( Pilot valve )
Hydraulic hoses ( Auxiliary lines )
Seat belt

Working

equipment

Engine connection

Machine

body

Every 2 years

Every 3 years

Hydraulic

system

Fuel system

Heater & AC systems

«
...
103
104
105
106
107
...
»

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов