manualshive.com logo in svg

Takeuchi TB175, Руководство оператора, Страница: 140 / 231

Поделиться
Скачать
Takeuchi TB175 Скачать руководство пользователя страница 140

137

MAINTENANCE

When Required

Inspecting the Rubber Crawlers

Repair or replace the rubber crawlers if their
conditions are as described below. Consult
a Takeuchi sales or service outlet about
repairs or replacement.

Rubber crawler
Replace the crawler if the entire crawler is
stretched and cannot be adjusted.

(1) Lug

Replace if the height of (A) is 5 mm (0.2 in.)
or below.

(2) Steel cord

Replace if the steel cord is exposed over 2
or more links.
Replace if half or more of the steel cords on
one side are cut.

(3) Metal core

Replace if even one metal core is off.

(4) Rubber

Repair if there are cracks of 60 mm (2.4 in.)
or greater in length.
If the steel cord is visible, repair as soon as
possible, regardless of the length of the
crack.

60 mm or greater

E4G065

E4G064

3

E4G062

3

2

1

A

4

E4G063

2

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов