Takeuchi TB175 Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 231

Takeuchi TB175 Скачать руководство пользователя страница 149

146

TROUBLESHOOTING

If a light does not turn on or the electric
system does not operate, a fuse may be
blown. Inspect the fuses.

Inspecting and Replacing the
Fuse

WARNING

If the fuse blows as soon as it is replaced,
there is a problem with the electric
system. Continued use may lead to fire.
Consult a Takeuchi sales or service
outlet.

1. Turn the starter key to the OFF position

and stop the engine.

2. Open the fuse box cover (1).
3. Inspect for any blown fuses.

4. If a fuse is blown, replace it with a spare

fuse of the same capacity.

If a Fuse Blows

Fuse Layout and Circuits Protected

10

10

10

20

20

10

20

10

5

10

5

10

20

20

20

10

1

L3J002

E4J007

Normal

Blown

Capacity

Capacity

Protected circuit

Protected circuit

15A Horn,

Interior Light

10A Proportional control

solenoid

20A Lights

20A Wiper

5A

Radio

5A

Heater

30A Air conditioner

(option)

20A Instrument cluster,

Lift alarm (option)

3A

Throttle controller
(B)

1A

Stop solenoid hold

10A External power socket

10A Cigarette lighter

10A Lever lock

10A Automatic-glow

20A Throttle controller

(ACC)

20A Feed pump,

Stop solenoid timer

«
...
147
148
149
150
151
...
»

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов