Takeuchi TB175 Скачать руководство пользователя страница 50

Страница: 50 / 231

CONTROLS

Instrument Cluster

Meters

12. Hour Meter

This displays the total engine
running time in hours.
The rightmost digit indicates
tenths of hours (6 minutes).

Set the inspection and maintenance intervals
according to the time displayed on the hour
meter.

13. Water Temperature Gauge

This gauge indicates the
temperature of the engine
coolant water.
The needle should be within

the green range during machine operation.
The red range indicates overheating.

14. Fuel Gauge

This gauge indicates the
amount of fuel in the tank.
Be sure to top off the tank
before running out of fuel.

C4B014

Indicators

8. Glow Lamp

This lamp turns off when
engine preheating is
completed.

9. Travel Speed Lamp

This lamp lights when the
travel speed switch is set to
2nd (high speed).

10. Slow Speed Slew Lamp

This lamp lights when slow
speed slew switch pressed,
the slew speed decreases.

11. Power Mode Lamp

These lamps indicates the
engine speed.

L3B017

L3B018

L3B019

L3B020

L3B021

C4B013

Содержание TB175








































































































































































































































Результаты поиска

Содержание TB175

Отзывы:

Takeuchi TB175, Руководство оператора, Страница: 50 / 231

Результаты поиска

Содержание TB175

Отзывы: