Takeuchi TB175 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 231

Takeuchi TB175 Скачать руководство пользователя страница 77

74

OPERATION

Machine Operation

Stopping Travel

WARNING

¡

¡

¡

¡

¡

Park the machine on firm, level ground
and apply the parking device. If you
must park on a slope or incline, block
the machine securely to prevent
movement.

¡

¡

¡

¡

¡

If any controls should be touched
accidentally when the safety lock lever
is lowered, the machine will move
suddenly, and cause serious injury or
death.

¡

¡

¡

¡

¡

Note that the dozer blade control is not
locked, even when the safety lock lever
is set to the lock position. Do not touch
this control accidentally.

CAUTION

Never bring the machine to a sudden stop
except in the case of a true emergency.
Stop as gently as possible.

1. Slowly set the left and right travel levers

to the neutral position. The machine stops.

Neutral

Neutral

Spin Turn

a

To spin left:
Tilt the left lever backward and the right
lever forward.

e

To spin right:
Tilt the right lever backward and the left
lever forward.

Neutral

E4D019

E4D020

«
...
75
76
77
78
79
...
»

Содержание TB175








































































































































































































































Отзывы:

Нет отзывов