Takeuchi TB175 Скачать руководство пользователя страница 97

Страница: 97 / 231

TRANSPORT

Cautions on Transporting

WARNING

Know and follow the safety rules,
vehicle code and traffic laws when
transporting the machine.

Consider the length, width, height and
weight of the truck with the machine
loaded on it when determining the best
route.

TRANSPORT

Securing the Machine

After loading the machine in the designated
position, secure it as described below.

Transporting Posture

1. Lower the dozer blade.
2. Fully extend the bucket and arm cylinders,

then lower the boom.

3. Stop the engine and remove the starter

key.

4. Raise the safety lock lever to engage the

lock.

5. Set stoppers in front and behind the

crawlers.

6. Put a chain or wire rope over the lower

frame and fasten it securely to prevent
sideways slippage.

7. Secure the bucket with a chain or wire

rope.

IMPORTANT: Place a wooden block
under the bucket so that it is not damaged
by hitting the floor.

Wire rope

Padding

E4F002

Содержание TB175








































































































































































































































Результаты поиска

Содержание TB175

Отзывы:

Takeuchi TB175, Руководство оператора, Страница: 97 / 231

Результаты поиска

Содержание TB175

Отзывы: