Takeuchi TB175 Скачать руководство пользователя страница 78

Страница: 78 / 231

OPERATION

Machine Operation

Slewing

WARNING

Check the surrounding area for safety
before slewing.

To slew left:
Tilt the left operating lever to the left.

To slew right:
Tilt the left operating lever to the right.

Operating the Boom

To lower the boom:
Tilt the right operating lever forward.

To raise the boom:
Tilt the right operating lever backward.

Operating the Working
Equipment

WARNING

Be careful to check which pattern of
lever control arrangement you are
operating with before beginning
operations.

The explanations in this manual are for
the ISO pattern.

Use the right operating lever to operate the
boom and bucket.
Use the left operating lever to operate the
arm and for slewing.
Return the operating levers to the neutral
position to stop the hoe attachments.

1. Set the safety lock lever to the released

position.

2. Set the pedal lock to the released position.

C4D006

E4D021

E4D022

Содержание TB175








































































































































































































































Результаты поиска

Содержание TB175

Отзывы:

Takeuchi TB175, Руководство оператора, Страница: 78 / 231

Результаты поиска

Содержание TB175

Отзывы: