manualshive.com logo in svg

Stratasys uPrint, Руководство по обслуживанию, Страница: 83 / 383

Поделиться
Скачать
Stratasys uPrint Скачать руководство пользователя страница 83

 

4-36

Installing the SATA hard drive

1.

Using a Phillips screwdriver, reinstall the 2 mounting brackets.

2.

Push the hard drive in the slots and down into position. 

3.

Using a Phillips screwdriver, reinstall the 4 mounting screws. 

4.

Reconnect the SATA cable.

5.

Reconnect the power input cable. 

6.

Close the electronics bay. See 

Closing the electronics bay on page

 

4-16.

7.

Power up the printer. The printer may take up to 45 minutes to run the Check Disc 

command before any text is displayed on the display panel. 

8.

After the printer has rebooted and is idle, press 

Maintenance > System > Set Network.

9.

Select either Dynamic networking or Static networking.

10.

If using Static networking, enter the printers IP Address, Default Gateway and Subnet 

Mask values.

11.

From the PC, open the CatalystEX.

12.

Connect to the printer.

13.

Insert the printer firmware CD into the workstation CD drive.

14.

From the Printer Services tab, click on the Update Software button.

15.

Navigate CatalystEX to the Upgrade (.UPG) file on the printer firmware CD.

16.

The printer will load, reboot and verify the upgrade.

17.

If the printer has System Software version 9.0 build 3230 or newer installation is 

complete. If the printer System Software is older than version 9.0 build 3230, complete 

the following steps:

A. 

Remove the printer calibration CD from the electronics bay and insert into the 

workstation CD drive. 

B. 

Install and open MaracaEX. Ensure that communications has been established 

with the printer.

C. 

Select “Send” and browse to the CD drive. 

D. 

Select the xxx.cal (where xxx equals printer name) from the CD by double 

clicking on the file name. 

E. 

To complete sending the file, click on the green check mark. This will write the 

file to the printer hard drive.

F. 

Cycle power on the printer.

G. 

Replace the CD into the electronics bay.

H. 

Perform Offset calibrations, see 

Offset Calibrations on page

 

5-2.

I. 

Perform Part Based calibration, see 

Part Based Calibration on page

 

5-7.

Содержание uPrint
































































































































































































































































































































































































Отзывы:

Нет отзывов