manualshive.com logo in svg

Stratasys uPrint, Руководство по обслуживанию, Страница: 286 / 383

Поделиться
Скачать
Stratasys uPrint Скачать руководство пользователя страница 286

uPrint/uPrint SE Service Manual

6-19

 

14,96       Unidentified interrupt 

occurred

1.

Cycle power.

14,97       Invalid data type

1.

Cycle power.

14,98       Find home failed, X EOT time-

out

14,99       Find home failed, Y EOT time-

out

1.

Power cycle machine - remember to move head away from switches.

2.

Using LED's check to see limit box toggles when switch is activated. If 

not, check switch and/or umbilical cable for X, Y cable for Y.

3.

X errors - Check pins and re-seat connector J505 on the I/O Card. Y 

errors - Check pins and re-seat connector J503 on the I/O Card.

14,100     Find home failed, Z HOME 

(BOT) not tripped

14,101     Find home failed, Z EOT not 

tripped

14,102     Find home failed, Z HOME 

(BOT) time-out

14,103     Find home failed, Z EOT time-

out

1.

Check for objects/parts on Z stage and around lead screw.

2.

Cycle power.

3.

Check Z Home and Z EOT LED's on PDB to verify state changes 

correctly. If not, check connector P8 on the PDB and Z switches. 

Replace cable and/or switches.

4.

Replace Z axis motor and lead screw.

5.

14.101 error only - Check 5/12 VDC power (5 and 12VDC LEDs will 

repeatedly dim) Replace 5/12 VDC power supply.

14,104     Surface not found

1.

No modeling base. Install modeling base.

2.

Modeling base is used/defective, has low spot. Replace Modeling 

base.

3.

Verify substrate sensor is working. If not, replace Substrate Sensor.

14,105     Controller not ready to build a 

model

1.

Cycle power.

14,106     BOT offset is higher than the 

BOT switch

1.

Use MaracaEX to zero the Z offset value.

2.

Run tip Z calibration.

3.

Check Z home sensor.

14,107     End model command while 

not modeling

Software error; will not be displayed.

14,108     Operation was killed

Software error; will not be displayed.

14,109     Out of memory

Software error; will not be displayed.

14,110     Cartridge communication 

error

1.

Replace material spool.

2.

Replace material carrier.

3.

Replace material bay.

14,111     Invalid frame check sequence

1.

Cycle power.

2.

If error repeats, replace Controller Board.

14,112     EEPROM communication error

Software error; will not be displayed.

14,113     Door not latched

1.

Verify chamber fans are operational. If not, replace 24VDC power 

supply.

2.

Inspect solenoid and wiring. 

3.

Replace solenoid.

4.

Replace PDB.

14,114     Thermocouple snap switch 

tripped

Not used on uPrint, uPrint SE, uPrint Plus and uPrint SE Plus printers.

14,115     Z stage planarity beyond toler-

ance

1.

Replace modeling base.

2.

Re-level XY table.

14,116     I2C configuration info is cor-

rupt

Software error; will not be displayed.

14,117     A command failed while mod-

eling

1.

Download CFG file - check error code details.

2.

Toggle failure - reference 14,129.

3.

Check and re-seat connectors/pins on J506 on the I/O card and J301 

on the head board.

4.

Replace Toggle Head assembly.

5.

Replace PDB (U8 chip failure).

14,118     Invalid cyclic redundancy 

check

Software error; will not be displayed

Code

Description

Corrective Actions

Содержание uPrint
































































































































































































































































































































































































Отзывы:

Нет отзывов