Stratasys uPrint Скачать руководство пользователя страница 358

Страница: 358 / 383

uPrint/uPrint SE Service Manual

7-15

Chamber light bar replacement

Power down the printer.

Locate the wiring harness leading away from the top of the light bar.

Disconnect the light bar from the wiring harness by squeezing the wiring harness clip

while pulling down.

Remove the light bar by removing the three attachment screws (top, middle, bottom) -

use the 7/64 T-handle wrench supplied in the startup kit.

Install a replacement light bar with the three attachment screws - do not overtighten the

screws.

Re-attach the wiring harness lead.

Figure 7-417: Chamber light bar locations

Содержание uPrint
































































































































































































































































































































































































Результаты поиска

Содержание uPrint

Отзывы:

Stratasys uPrint, Руководство по обслуживанию, Страница: 358 / 383

Результаты поиска

Содержание uPrint

Отзывы: