SICK Inspector PIM60 Скачать руководство пользователя страница 76

Страница: 76 / 84

Table B.23

Error codes - Configuration errors

Description

Error code

No error

Operation is not allowed in current mode

8100

The reference bank is not used on the device

8101

Operation is not allowed, for example trying sINT 20 0 when not in calibration

mode

8102

Calibration mode is not enabled when trying to perform calibration or trying to

remove non-existent calibration

8103

No object locator is available in current reference bank

8104

No blob tool with this index exists

8105

Polygon defect detection is not enabled

8106

No polygon with supplied index exists

8107

No pixel counter with supplied index exists

8108

No edge pixel counter with supplied index exists

8109

No pattern inspection with supplied index exists

8110

The move or rotation caused the ROI to appear outside of the FOV

8111

Trig is not activated

8112

The specified IP address was invalid, or an invalid combination of addresses

was used

8113

The specified network mask was invalid

8113

The specified gateway address was invalid

8113

The combination of IP settings was invalid

8113

Calibration failed

8114

Interface not available. Only interfaces that exist in the product can be en-

abled/disabled

8115

No edge tool with supplied index exists

8116

No angle tool with supplied index exists

8117

No circle with supplied index exists

8118

No distance tool with supplied index exists

8119

The specified tool does not have a region (it is a measurement)

8120

The tool type of the specified tool does not support this command

8121

No tool with supplied index exists

8122

No edge count tool with supplied index exists

8123

Search region is not enabled

8124

Width or height is invalid

8125

No tools in configuration

8126

Invalid unit specified

8127

Alignment to specified control points failed

8128

8015726/ZPP7/2018-

Subject to change without notice

Reference Manual

Command channel

Appendix

Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды