SICK Inspector PIM60 Скачать руководство пользователя страница 45

Страница: 45 / 84

Comment

Binary

Range

Attribute

Value tag

Container tag

Edge matching score.

REAL

[0, 100]

SCORE

In degrees or radians depend-

ing on attribute “unit” or con-

REAL

[0, 180]

unit

ANGLE

figured value in the

Ethernet

Result output

dialog.

0=not found, 1=found, 2=Out-

side image

USINT

{0, 1, 2}

DECISION

Name attribute required if

more than one Circle exist

any string

name

CIRCLE_LOCAT-

X position of the reference

point. In “pixels” or “mm” de-

REAL

coordUnit

pending on attribute “co-

ordUnit” or configured value in

the

Ethernet Result output

dialog.

Y position of the reference

point. In “pixels” or “mm” de-

REAL

coordUnit

pending on attribute “co-

ordUnit” or configured value in

the

Ethernet Result output

dialog.

Circle matching score.

REAL

[0, 100]

SCORE

Circle's diameter in pixels or

mm depending on attribute

REAL

coordUnit

DIAMETER

"coordUnit" or configured value

in the

Ethernet Result output

dia-

log.
0=not found, 1=pass, 2=Out-

side image, 11=Failed on score

value, 12=Failed on diameter

USINT

{0, 1, 2,

11, 12}

DECISION

Name attribute required if

more than one Measure dis-

tance exists

any string

name

MEASURE_DIS-

TANCE

Measured distance in pixels or

mm depending on attribute

REAL

coordUnit

DISTANCE

“coordUnit” or configured value

in the

Ethernet Result output

dia-

log.
Indicates whether the value in

the distance tag is a valid

USINT

{0, 1}

VALID

measurement or not. 0=Invalid

1=Valid
0=fail (measure distance could

not be done), 1=pass

USINT

{0, 1}

DECISION

Name attribute required if

more than one Measure Angle

exist

any string

name

MEAS-

URE_ANGLE

X position of the intersection

point. In “pixels” or “mm” de-

REAL

coordUnit

pending on attribute “co-

ordUnit” or configured value in

the

Ethernet Result output

dialog.

Subject to change without notice

8015726/ZPP7/2018-

Appendix

Result output formatting

Reference Manual
Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды