SICK Inspector PIM60 Скачать руководство пользователя страница 32

Страница: 32 / 84

</CORNERS>

</POLYGON>

Analyzed image’s number, attributes dataType and pos
Start of container for Polygon, Name refers to the Polygon tool's name in the

Tools

tab

Number of corners used for this Polygon tool
Number 0 to 15 gives the properties of a single corner. The index of this corner is the

order in which the polygon corner was added when the polygon was drawn

Polygon corner coordinate (x), "pixels" or "mm"
Polygon corner coordinate (y), "pixels" or "mm"
End of tag for corners
End of container for Polygon

Attribute dataType

Casts to the specified datatype. When using EtherNet/IP the at-

tribute dataType specifies the dataType section in the selected

assembly. The attribute dataType can be SINT, INT, DINT or REAL.

For more details about dataType and pos see table in Sec-

tion A.3.2, “

Attributes

” (page 50).

Attribute pos

Used by EtherNet/IP to determine a position in the dataType

section in the selected assembly. The first position number of

the dataType section is 0. The range of the attribute pos depends

on which assembly is used. For example if assembly 1 and

dataType section SINT is selected the range of position is 8, i.e.

[0, 7]. For more details about dataType and pos see table in

Section A.3.2, “

Attributes

” (page 50).

Therefore the value of the attributes dataType and pos together specifies which parameter

in the assembly the result value should be mapped to.

Result of validating output string with only a Polygon

The validating in

SOPAS Engineering Tool (ET)

will give the following result:

EtherNet/IP assembly string OK.

If the used assembly is too small the validating will give the following result:

EtherNet/IP assembly string not OK. Out of slots for data type INT

Use a larger assembly to solve this problem . Choose a larger assembly in the dialog

Interfaces

and I/O settings

in the

InspectorPIM60

menu and the

EtherNet/IP

tab.

Result in PLC with only a Polygon

The table below describes how the Assembly 1's data structure will be populated when using

the configuration example above.

Variable from
example above

Offset byte

Data type

(dataType)

Position ref (pos)

from XML configuration

NUM_CORNERS

SINT

8015726/ZPP7/2018-

Subject to change without notice

Reference Manual

EtherNet/IP

Interfaces

Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды