SICK Inspector PIM60 Скачать руководство пользователя страница 15

Страница: 15 / 84

Example URLs

http://192.168.1.110/LockLog

http://192.168.1.110/LockLog?Unlock

Retrieve a logged image without overlay graphics:

http://192.168.1.110/LogImage.jpg?00

Retrieve a logged image with overlay graphics:

http://192.168.1.110/LogImage.jpg?00&ShowOverlay

Retrieve a logged image with simplified overlay graphics:

http://192.168.1.110/LogImage.jpg?00&SimplifiedOverlay

3.2.5

Statistics

To retrieve statistics using the command channel, execute the following command:

gSTAT

Statistics can also be retrieved using the URL:

http://<IP-address>/CmdChannel?gSTAT

The response is

rgSTAT 0

followed by an XML formatted string. To read the response in an

web browser, change the view in the web browser to reflect the source code.

Note

The statistic response is only for the active reference object.

3.3

Control the sensor via Web API

The Web API supports using the command channel for reading and updating parts of the

device configuration.
The Web API also supports the functionality to do a backup of the device configuration to a

file and to restore the configuration again. This is a convenient way to handle configurations

without installing and using

SOPAS Engineering Tool (ET)

3.3.1

Basic principles

The command channel has a set of basic principles:
• Only one command at a time can be executed.
• Inspector PIM60 responds to each command with a response that includes the result of

the command as well as error codes.

• A specific task to control the Inspector PIM60 includes the command together with its

parameters, see list of command types and parameters in Appendix B, “

Command chan-

nel

” (page 52).

• Writing a parameter can typically only be done when the device is in Edit mode. Reading

a parameter can be done in both Edit and Run mode.

• It is possible to block configuration changes by deselecting

Allow changes via Web Server

the

Web Server

tab in the dialog

Interfaces and I/O Settings

InspectorPIM60

menu.

3.3.2

Command syntax

The Web API command channel has the following syntax:

http://<IP-address>/CmdChannel?<command>_<identifier>_<argument

1>_<argument 2>..._<argument N>

The

ACK

message has the following syntax:

<ACK Command> <identifier> <errorCode> <returnValue1> <returnValue2> ...

The command is sent as an ASCII string. The combination of a command with its parameters

will either change the device configuration or fetch information from the device. For more

Subject to change without notice

8015726/ZPP7/2018-

Interfaces

Web interface

Reference Manual
Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды