SICK Inspector PIM60 Скачать руководство пользователя страница 49

Страница: 49 / 84

A.3.1

General tags

Table A.2

Generic output string tags

Comment

Binary

Range

Attrib-

ute

Value tag

UINT

MESSAGE_SIZE

• Binary format: The size of the message

in bytes

• ASCII format: The number of characters

in the message

Analyzed image's number (Resets at

power-up or device reset)

UDINT

IMAGE_NUMBER

0=Not located, 1=Detail failed, 2=All

passed 3=Not located and detail failed

USINT

[0, 3]

IMAGE_DECISION

Reference object index

USINT

[0, 31]

REF_OBJECT

Used to send single control characters

IGNORED

[0, 255]

value

ASCII

Same as <ASCII value="32"/>

IGNORED

SPACE

Same as <ASCII value="9"/>

IGNORED

TAB

Left angular bracket, "<". Useful when

generating XML-formatted output.

IGNORED

LAB

Right angular bracket, ">". Useful when

generating XML-formatted output.

IGNORED

RAB

Same as <ASCII value="10"/>

IGNORED

NEWLINE

Same as <ASCII value="13"/>

IGNORED

RETURN

Current time since device boot. Restarts

from zero after ~10 years (using seconds)

and ~49 days (using milliseconds)

UDINT

{s, ms}

timeUnit

TIME

Device serial code.

UDINT

SERIALCODE

Only valid while the device is in Edit mode.

This is the focus value from the

Image

settings

tab

REAL

[0, 100]

FOCUS

A counter that increments for each tele-

gram sent over the result channel. Resets

at power-up or device reset.

UINT

TELE-

GRAM_COUNTER

If the intValue attribute is not specified

the default value will be zero and the tag

can be used for padding.

USINT

[0, 255]

intValue

USINT

If the intValue attribute is not specified

the default value will be zero and the tag

can be used for padding.

UINT

[0, 65535]

intValue

UINT

If the intValue attribute is not specified

the default value will be zero and the tag

can be used for padding.

UDINT

[0, 2

-1]

intValue

UDINT

Value can be changed through the com-

mand channel.

UINT

[0, 65535]

intValue

UINT1

Value can be changed through the com-

mand channel.

UINT

[0, 65535]

UINT2

Subject to change without notice

8015726/ZPP7/2018-

Appendix

Result output formatting

Reference Manual
Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды