SICK Inspector PIM60 Скачать руководство пользователя страница 9

Страница: 9 / 84

2.2.1

Basic configuration of the IP address

The address selection switch on the I/O extension box configures the host part of the IP ad-

dress, that is, the last of the four parts of the IP address. By default, the first three parts of

the address (also known as the network address) are set to 192.168.1. If the switch is set

to a value other than 0 (all switches set to Off) or 255 (all switches set to On), the I/O extension

box will use the host part of the IP address assigned by the switch.

Figure 2.2

Example

The setting above configures the I/O extension box to have a host ID of 3 corresponding to

the binary value “00000011” where switch 1 is bit 0 (LSB) and switch 8 is bit 7 (MSB). The

I/O box will then have an IP address of 192.168.1.3.

Advanced configuration of the IP address

If the network part of the IP address must be changed from the default 192.168.1 for the

I/O extension box, the internal web server of the I/O extension box can be used. For details

please refer to the manual delivered with the I/O extension box.

2.3

Setup of the I/O extension box in the SOPAS Engineering Tool

(ET) application

The communication with the I/O extension box is configured using the

InterfacesandI/OSettings

dialog from the

InspectorPIM60

menu. Check the

Digital I/O

and

I/O extension

boxes in the

Inter-

faces

tab. The I/O extension box is disabled if

EtherNet/IP

is selected in the same tab.

Figure 2.3

I/O Extension Box setup

Communication mode

It is possible to adjust the way that the Inspector is communicating with the I/O extension

box. The settings are made in the

I/O extension box setup

tab in the

Interfaces and I/O Settings

dialog from

InspectorPIM60

menu. There are three modes available:

• Robust mode. This is the default communication mode, and it is the recommended one if

the Inspector is connected to the

SOPAS Engineering Tool (ET)

application during operation.

• Fast mode. This mode allows the Inspector to operate at a higher frame rate but there is

a risk that some data in the communication with the I/O extension box is lost if there is

high load on the network. This mode shall not be used if the Inspector is connected to the

SOPAS Engineering Tool (ET)

application during operation.

• User mode. This is the advanced communication mode where it is possible to configure

the number of retries that the Inspector performs, and the timeout for each retry. The

timeout is the time (in milliseconds) that the Inspector is waiting for a reply from the I/O

extension box for a request to set outputs or read inputs.

Subject to change without notice

8015726/ZPP7/2018-

Interfaces

I/O extension box

Reference Manual
Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды