SICK Inspector PIM60 Скачать руководство пользователя страница 12

Страница: 12 / 84

could not be found an error message is displayed, for instance

Requesttimedout

Destination

host unreachable

Example

: ping 192.168.1.3

•

Ipconfig

. Open the command prompt and type

ipconfig

. The current status for the network

cards on the PC will then be displayed. Ensure that the network settings are corresponding

to the setting for the I/O extension box. The current IP address for the Inspector can be

viewed by selecting Device Info from the

InspectorPIM60

menu.

The web browser on the PC must be configured not to use a proxy when communicating with

the web server in the I/O extension box.

2.5.3

High number of unanswered requests to the I/O extension box

The advanced communication mode, User mode, can be used to fine tune the communication

with the I/O extension box. It is recommended to try to increase the timeout as a first step,

and if this does not work, try to increase the number of retries. Increasing the number of retries

will reduce the inspection speed.
If the problem persists even if the timeout and the number of retries have been increased,

verify that the network topology does not block the use of UDP packets.

8015726/ZPP7/2018-

Subject to change without notice

Reference Manual

I/O extension box

Interfaces

Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды