SICK Inspector PIM60 Скачать руководство пользователя страница 58

Страница: 58 / 84

Range

Return values

Arguments

Us-

able

Run

mode

Iden-

tifier

Com-

mand

Description

ticks, 200000

ticks]
[0,19], [0=ms,

1=tick],

int outputIn-

dex, int

sINT

Set digital output act-

ive time

[1,10000] resp [0

type, int

ticks, 200000

ticks]

time (milli-

seconds*10

or ticks)

[0,19], [0=ms,

1=tick],

int type, int time

(milliseconds*10

or ticks)

int outputIn-

dex

Yes

gINT

Get digital output act-

ive time

[1,10000] resp [0

ticks, 200000

ticks]
[0=A, 1=B, 2=C,

3=D]

int pointIn-

dex,

300

sINT

Set alignment control

point

int x * 100, [-

2147483648,

2147483647]

int x * 100,
int y * 100
int z * 100

int y * 100, [-

2147483648,

2147483647]
int z * 100, [-

2147483648,

2147483647]

While possible to trig over all interfaces, it is recommended to use only the following for high speed applications:

• Digital I/O (In3)

• Ethernet Raw (port 2116)

• EtherNet/IP (small assembly)

The exposure is expressed in ms multiplied by 100 i.e. 3.8 ms is expressed as 380

The result is 0= normal mode or 1= calibration mode.

The result is 0= not calibrated or 1= calibrated.

The result is expressed in mm/pixel x 10000.

The result is expressed in pixels for x and y.

The result is expressed in degrees.

The delay is expressed in ms multiplied by 10 i.e. 1.5 ms is expressed as 15

In order for the settings to take effect the aACT 7 command needs to be sent to the device

Table B.7

Command channel functions - Object locator

Range

Return

values

Argu-

ments

Usable

in Run

mode

Identi-

fier

Com-

mand

Description

[0, 100], percent

int

threshold

sINT

Change object locator

match threshold

[0, 100], percent

int

threshold

Yes

gINT

Get object locator

match threshold

0=off, 1=on

int mode

sINT

Change object locator

rotation search mode

8015726/ZPP7/2018-

Subject to change without notice

Reference Manual

Command channel

Appendix

Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды