SICK Inspector PIM60 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 84

background image

The EDS file for the Inspector PIM60 can be found in the SICK Support Portal (support-

portal.sick.com).
The Inspector PIM60 has two Output assemblies that can be used for controlling the Inspector.

To do this the connection has to be set first, see Operating Instructions for Inspector PIM60.
The slim command channel assembly (instance no. 100) is used for controlling the Inspector

in the following ways:
• Select reference object
• Image trig
The command channel assembly (instance no. 102) is also used for controlling the Inspector.

With this assembly you have access to all functions in the command channel, see Section B.3,

Command descriptions

The two output assemblies are described in detail, see Section 5.3.6, “

Assemblies command

5.3.1

Basic principles

The command channel has a set of basic principles:
• In order to be able to change the configuration via EtherNet/IP this must be enabled. This

is done In the dialog

Interfaces and I/O Settings

from the

InspectorPIM60

menu. Check

Ethernet

and

EtherNet/IP

in the tab

Interfaces

. In the same dialog and tab

EtherNet/IP

check

Allow

changes via EtherNet/IP

.

• It is possible to block configuration changes by deselecting the setting

Allow changes via

EtherNet/IP

in the

EtherNet/IP

tab in the dialog

Interfaces and I/O Settings

in

InspectorPIM60

menu.

• Writing a parameter can typically only be done when the device is in Edit mode. Reading

a parameter can be done in both Edit and Run mode.

• The commands is sent with help of output assembly 102 and the result is received with

input assembly 101.

• The result for a sent command can be received at the earliest in the next PLC cycle. The

PLC program will have to wait for the result for an undefined number of seconds.

• Make sure that the PLC program waits for a response with the same command and ID as

the sent command.

5.3.2

Command syntax

To send commands through the command channel use output assembly 102. The command

channel has the following syntax:

<arg 6>

<arg 5>

<arg 4>

<arg 3>

<arg 2>

<arg 1>

<identifier>

<command>

Replace

<command>

with the commands id, see Table B.3, “Command ID numbers - for Eth-

erNet/IP” (page 54).
The result of a command, sent over output assembly 102, can be received through input

assembly 101. The syntax for ACK message is:

<retVal6>

<retVal5>

<retVal4>

<retVal3>

<retVal2>

<retVal1>

<error

code>

<identifier>

<command>

The combination of a command with its parameters will either change the devices configur-

ation or fetch information from the device. For more command examples see Section B.1,

Command syntax

” (page 52) and Section B.6, “

Command examples

5.3.3

Select reference object

There are two ways to select reference object with EtherNet/IP and command channel.

8015726/ZPP7/2018-

09

©SICK AG • Identification & Measuring • www.sick.com • All rights reserved

Subject to change without notice

34

Reference Manual

EtherNet/IP

Interfaces

Inspector PIM

«
...
32
33
34
35
36
...
»

Содержание Inspector PIM60





















































































Отзывы:

Нет отзывов

Похожие инструкции для Inspector PIM60

Бренд: Canon Страницы: 14

IMAGE STABILIZER EF70-200MM F/4L IS USM

Бренд: Canon Страницы: 13

TIMER REMOTE CONTROLLER TC-80N3

Бренд: Canon Страницы: 3

TIMER REMOTE CONTROLLER TC-80N3

Бренд: Canon Страницы: 2

EF-S55-250mm f/4-5.6 IS II

Бренд: Canon Страницы: 7

mydlink DSP-W110

Бренд: D-Link Страницы: 13

Бренд: D-Link Страницы: 44

Бренд: Panasonic Страницы: 40

Resusci Baby QCPR

Бренд: laerdal Страницы: 8

Бренд: Olympus Страницы: 2

Бренд: Uniden Страницы: 16

Бренд: Uniden Страницы: 20

1306 RAPID SYSTEM

Бренд: Thule Страницы: 8

Бренд: Woody Valley Страницы: 15

Бренд: Acuity Brands Страницы: 3

AAB-P-RZR900-K2-001

Бренд: SuperATV Страницы: 3

Бренд: Omega Engineering Страницы: 13

Бренд: Gardena Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды