SICK Inspector PIM60 Скачать руководство пользователя страница 77

Страница: 77 / 84

B.5

Version information

The command channel is continually extended with new commands. The intention is to always

keep the command set backwards compatible with earlier versions. This table lists the

available versions and the updates between each version.

Table B.24

Command channel versions

Comments

Released in

Version

First official version

PIM60 1.0

B.6

Command examples

B.6.1

Command examples Ethernet Raw

Note that the ACK messages in the below tables don't include the start and end character

that is included in all ACK messages. See Section B.1, “

Command syntax

” (page 52) for more

information on start and end character.

Table B.25

Commands Ethernet Raw - general examples

ACK message

Command

Description

rsMOD 0

sMOD 0

Switch to Run mode

rsMOD 0

sMOD 1

Switch to Edit mode

rgMOD 0 1

gMOD

Get device mode

rsINT 16 0

sINT 16 0

Set trigger mode to free-running

rsINT 16 0

sINT 16 1

Set trigger mode to triggered

rgINT 16 0 0 – if free-running
rgINT 16 0 1 – if triggered by Ether-

net

gINT 16

Get trigger mode

rsINT 69 0

sINT 69 2 200 255

Set defect intensity thresholds to

200-255 for polygon 2

rgINT 69 0 200 255 – if OK
rgINT 69 8107 polygon does not ex-

ist – if not OK

gINT 69 2

Get defect intensity thresholds for

polygon 2

rgSTR 2 0 Object 2 - if OK
rgSTR 2 8000 Ref bank index is not

used. - if not OK

gSTR 2 1

Get name of second reference ob-

ject

rgSTR 8 0 Polygon 2 - if OK
rgSTR 8 8107 No polygon with this

index exists. - if not OK

gSTR 8 1 1

Get name of second polygon in

second reference object

Subject to change without notice

8015726/ZPP7/2018-

Appendix

Command channel

Reference Manual
Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды