SICK Inspector PIM60 Скачать руководство пользователя страница 10

Страница: 10 / 84

IP configuration

To be able to connect to the I/O extension box, the IP address of the I/O extension box must

be specified in the

SOPAS Engineering Tool (ET)

application.

To specify the IP address of the I/O extension box:
1. Open the

InterfacesandI/OSettings

dialog from the

InspectorPIM60

menu. Enter the selected

IP address of the

I/O extension box setup

tab in the four fields separated with dots.

2. Click

Apply

to store the settings.

Figure 2.4

Set up mode and IP address

Verify connection

It is possible to verify that the connection to the I/O extension box can be established by

clicking the

Verify connection

button. The

SOPAS Engineering Tool (ET)

application will then try to

connect to the I/O extension box, and a message will be displayed informing if the I/O exten-

sion box was found.

Note

It is possible to configure the Inspector for use with the I/O extension box even when the I/O

extension box is not available. As soon as the Inspector detects the I/O extension box on the

network, it will connect to it and start using it as configured.

2.3.1

Enabling the I/O extension box

The use of the inputs and outputs on the I/O extension box is enabled on the

Digital I/O

tab

of the

Interface and I/O Settings

dialog from the

InspectorPIM60

menu.

2.4

Input and output connections

When delivered, the I/O extension box contains 4 digital inputs and 8 digital outputs. The

digital outputs can be expanded to 16, and the digital inputs of the Inspector PIM60 can be

extended to 5.
Please refer to the manual delivered with the I/O extension box for details on how to connect

the power supply to the box, and where to find the digital inputs and outputs.

2.4.1

Special conditions during startup

The following applies if the Inspector is configured to use the inputs of the I/O extension box

for object selection:
If the I/O extension box is not available when the Inspector starts up, the Inspector will use

the last reference object that was selected in the

SOPAS Engineering Tool (ET)

application before

8015726/ZPP7/2018-

Subject to change without notice

Reference Manual

I/O extension box

Interfaces

Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды