SICK Inspector PIM60 Скачать руководство пользователя страница 22

Страница: 22 / 84

Ethernet Raw

4.1

Introduction

To set up the connection and output results for Inspector PIM60 using Ethernet Raw see

Operating Instructions for Inspector PIM60.

4.1.1

Port interval

The default interval for the ports used by the communication channels is 2114-2116. This

interval can be changed, e.g. if the controlling device does not support the default interval.

The interval is controlled by the field

Start port

in the

Ethernet Raw

tab of the

Interface and I/O

settings

dialog.

The ports are assigned according to the following:
• Ethernet Result Output = start port (default 2114)
• Command channel = start port + 1
• Dedicated image trig = start port + 2

4.2

Get results via Ethernet Raw

The following settings are configured in the

Ethernet Result Output

dialog under

InspectorPIM60

menu.

4.2.1

TCP versus UDP

The basic difference between these protocols, for the Ethernet result output function, is which

side initiates the connection to receive/send the data.

UDP:

TCP:

PC/PLC initiates the connection

Inspector sends results to the spe-

cified IP address and port, without

knowing if it has been received

Inspector sends results to the PC/PLC
PC/PLC acknowledges that results are re-

ceived (built into the TCP protocol)

Note

For TCP the default port number that the Inspector listens to is 2114.

4.2.2

ASCII versus binary

The Inspector supports the possibility to choose whether the configured output is to be sent

in ASCII format or in a binary format. The parameters that should be transferred in binary

format are also defined in the XML based formatting, but some tags are not supported in the

binary format.
If such a parameter is added to the formatting it will be ignored by the Inspector. In binary

mode all added text and text formatting, for example

, are ignored. Only the values

8015726/ZPP7/2018-

Subject to change without notice

Reference Manual

Ethernet Raw

Interfaces

Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды