SICK Inspector PIM60 Скачать руководство пользователя страница 44

Страница: 44 / 84

Comment

Binary

Range

Attribute

Value tag

Container tag

Name attribute required if

more than one Blob tool exists.

any string

name

BLOB

The name refers to the Blob

tool's name in the tool tab
Index of found blob according

to current blob sorting order.

Index 0 is the first blob

[0, 15]

index

Blob center of gravity (x posi-

tion). “pixels” or “mm” depend-

ing on attribute “coordUnit”

REAL

coordUnit

Blob center of gravity (y posi-

tion). “pixels” or “mm” depend-

ing on attribute “coordUnit”

REAL

coordUnit

Number of found blobs.

USINT

FOUND_
BLOBS

The lower threshold of the Blob

tool's intensity after applying

ambient light compensation.

USINT

LIVE_
THRESHOLD_
LOW

The upper threshold of the

Blob tool's intensity after apply-

USINT

LIVE_
THRESHOLD_

ing ambient light compensa-

tion.

HIGH

In degrees or radians depend-

ing on attribute “unit” or con-

REAL

[0, 180]

unit

ANGLE

figured value in the

Ethernet

Result output

dialog.

Blob area (in pixels). In “pixels”

or “mm

” depending on attrib-

UDINT

AREA

ute “coordUnit” or configured

value in the

Ethernet Result out-

put

dialog.

0 = blob fully within ROI, 1 =

blob touches ROI border

USINT

{0, 1}

EDGE_FLAG

Structure calculation value

(number of edge pixels inside

the found blob)

UDINT

EDGE_PIXELS

0=not found, 1=found

USINT

{0, 1}

DECISION

Name attribute required if

more than one Edge tool exist

any string

name

EDGE_LOCAT-

X position of the reference

point. In “pixels” or “mm” de-

REAL

coordUnit

pending on attribute “co-

ordUnit” or configured value in

the

Ethernet Result output

dialog.

Y position of the reference

point. In “pixels” or “mm” de-

REAL

coordUnit

pending on attribute “co-

ordUnit” or configured value in

the

Ethernet Result output

dialog.

8015726/ZPP7/2018-

Subject to change without notice

Reference Manual

Result output formatting

Appendix

Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды