SICK Inspector PIM60 Скачать руководство пользователя страница 47

Страница: 47 / 84

Comment

Binary

Range

Attribute

Value tag

Container tag

If the chosen Edge counter is

circular the value is the pitch

in degrees or radians depend-

ing on attribute “unit” or con-

figured value in the

Ethernet

Result output

dialog.

0=Not found, 1=Found,

2=Outside image

USINT

{0, 1, 2}

DECISION

X position for the mid point of

the feature/edge, see foot-

REAL

coordUnit

note

. In “pixels” or “mm” de-

pending on attribute “co-

ordUnit” or configured value in

the

Ethernet Result output

dialog.

Y position for the mid point of

the feature/edge, see foot-

REAL

coordUnit

note

. In “pixels” or “mm” de-

pending on attribute “co-

ordUnit” or configured value in

the

Ethernet Result output

dialog.

Only applicable for

Feature type

Single edge

. A positive value is

REAL

[0, 180]

ANGLE

a clockwise rotation and a

negative value is a counter

clockwise rotation.

The angle of the single edge in

degrees or radians depending

on attribute “unit” or con-

figured value in the

Ethernet

Result output

dialog.

Only applicable for

Feature type

Dark

Bright

. The edge's or

REAL

[0, 180]

INTERN-

AL_ANGLE

feature's angle in the search

region.

The angle of the feature in de-

grees or radians depending on

attribute “unit” or configured

value in the

Ethernet Result out-

put

dialog.

Only applicable for

Feature type

Dark

Bright

REAL

WIDTH

If the chosen Edge counter is

rectangular the value shows

the width “pixels” or “mm” de-

pending on attribute “co-

ordUnit” or configured value in

the

Ethernet Result output

dialog.

If the chosen Edge counter is

circular the value is the width

in degrees or radians depend-

ing on attribute “unit” or con-

Subject to change without notice

8015726/ZPP7/2018-

Appendix

Result output formatting

Reference Manual
Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды