SICK Inspector PIM60 Скачать руководство пользователя страница 11

Страница: 11 / 84

data was saved to flash. Once the I/O extension box is available, the Inspector will read the

inputs of the box, and select the corresponding reference object.

2.4.2

Connection to the I/O extension box lost during operation

If the connection to the I/O extension box is lost during operation, the last status of the inputs

on the box will be used until the connection is re-established.

2.4.3

Object selection with I/O extension box

The status of the inputs on the I/O extension box is checked in the end of each inspection

cycle. If the Inspector is configured to use external image trig, the status of the external inputs

will only be checked when an image trig signal has been received.

2.4.4

Timing issues

The digital outputs on the I/O extension box shall be read at minimum delay time as displayed

in the

SOPAS Engineering Tool (ET)

application.

2.4.5

Use of the digital outputs for logic

The digital outputs on the I/O extension box are not guaranteed to be jitter-free. It is not re-

commended to use these outputs for direct control of other devices. The I/O extension box

shall be connected to a PLC for process control.

2.4.6

Change of Modules in the I/O extension box

The Inspector PIM60 supports I/O extension box configurations with up to 16 digital outputs

and 5 digital inputs (The standard configuration of the I/O extension box contains 8 digital

outputs and 4 digital inputs.). The configuration of an I/O extension box can be changed by

adding/removing I/O modules to/from the I/O extension box. I/O modules are available as

an accessory from SICK. For details about Accessories Ordering information see the Operating

Instructions for Inspector PIM60.
Perform the following steps to connect and use more I/O modules:
1. Close the

SOPAS Engineering Tool (ET)

application.

2. Disconnect the power from the I/O extension box.
3. Connect the additional I/O modules (inputs and/or outputs) to the I/O extension box.

Please refer to the manual delivered with the I/O extension box for details.

4. Re-connect the power to the I/O extension box.
5. Re-start the

SOPAS Engineering Tool (ET)

application.

The additional digital outputs are now be available in the

SOPASEngineeringTool(ET)

application.

2.5

Troubleshooting

2.5.1

The I/O LED flashes 10 times

If the power to the I/O extension box has been disconnected for a longer period of time, the

internal clock in the box will be reset. The I/O LED on the box will then flash 10 times in red.

This is not a serious error, and the I/O extension box can still be used together with the In-

spector without any problems.

2.5.2

No contact with the I/O extension box

Ensure that the network card on the PC has the same network address, for instance

192.168.1, as the I/O extension box. The host part of the IP address (that is the last number

in the IP address) must not be the same as for the I/O extension box or the Inspector.
There are two tools available in Windows to check the network connection and the IP settings:
•

Ping

. Open the command prompt, and type

ping

followed by the IP address of the I/O exten-

sion box. If the I/O extension box is available the following text will be displayed:

Reply from

x.x.x.x

(where x.x.x.x is the IP address of the I/O extension box). If the I/O extension box

Subject to change without notice

8015726/ZPP7/2018-

Interfaces

I/O extension box

Reference Manual
Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды