SICK Inspector PIM60 Скачать руководство пользователя страница 55

Страница: 55 / 84

Table B.4

Command channel - actions

Range

Return

values

Argu-

ments

Usable in

Run mode

Identi-

fier

Com-

mand

Description

aACT

Save settings in

flash

0=use expos-

ure settings,

1=auto adjust

int auto-

Exp

Yes, only in

Run mode.

aACT

Re-teach reference

object

>0
[0,100]

-
int calib-

rationCov-

erage

int box-

Size

aACT

Perform calibration

aACT

Remove calibration

0=use manual

settings,

1=use DHCP

int useDH-

Yes

aACT

Apply IP settings

Both in run

and edit

mode

aACT

Restart the Inspect-

aACT

Perform (calculate)

coordinate align-

ment

In order to run this command the device must be set to Calibration mode (sINT 20 1).

The argument must be given in mm.

Returned value is the calibration target coverage in percent.

After the aACT 5 command has been executed the Inspector need to be restarted (e.g. using aACT 6) before the

new IP settings are in use.

The aACT 6 command will make the device being temporarily disconnected while it is rebooted.

This command can only be used if the 4 control points have been set via the sINT 300 command

Subject to change without notice

8015726/ZPP7/2018-

Appendix

Command channel

Reference Manual
Inspector PIM

Содержание Inspector PIM60





















































































Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды

SICK Inspector PIM60, Справочное руководство

Результаты поиска

Содержание Inspector PIM60

Отзывы:

Похожие инструкции для Inspector PIM60

Бренды по названию

Популярные бренды