SICK Inspector PIM60 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 84

background image

C

Restore configuration over Web API

The restore configuration operation takes a device configuration created with the backup

functionality and replaces the current configuration with the configuration in the backup file.

The operation is a multiple step procedure with the following steps:
1. Create session cookie
2. Login
3. Prepare restore mode
4. Transfer restore file to device
5. Device restart
The restore operation will remove the previous configuration and replace it with a new con-

figuration. The IP address and the chessboard calibration will not be updated by the restore

operation. It is not possible to use the device for other purposes during the restore operation.

The operation may take several minutes to perform and the time is partly depending on the

size of the backup file.

C.1

Restore configuration

The restore configuration operation takes a device configuration created with the backup

functionality and replaces the current configuration with the configuration in the backup file.

The operation is a multiple step procedure with the following steps:
1. Create session cookie
2. Login
3. Prepare restore mode
4. Transfer restore file to device
5. Device restart
The restore operation will remove the previous configuration and replace it with a new con-

figuration. The IP address and the chessboard calibration will not be updated by the restore

operation. It is not possible to use the device for other purposes during the restore operation.

The operation may take several minutes to perform and the time is partly depending on the

size of the backup file.

C.2

Create session cookie

A session cookie is used to handle operations requiring login with user name and password.

The session cookie is created before performing the login operation and the cookie must

then be supplied in the login operation and for all following operations.

Operations

CREATE COOKIE

C.3

Login

A login with the user name "Maintenance" is required to change information on the device.

The password is the password stored on the device. Default password is "Inspector".

Operations

CREATE SOCKET

CONNECT TO SOCKET(<IP address>, port = 80)

SEND HTTP POST REQUEST (to="/HandleConfig", data =

"sopas_username=Maintenance&sopas_password=<login_password>")

79

©SICK AG • Identification & Measuring • www.sick.com • All rights reserved

Subject to change without notice

8015726/ZPP7/2018-

09

Appendix

Restore configuration over Web API

Reference Manual
Inspector PIM

«
...
77
78
79
80
81
...
»

Содержание Inspector PIM60





















































































Отзывы:

Нет отзывов

Похожие инструкции для Inspector PIM60

Бренд: Panasonic Страницы: 16

Бренд: Hach Страницы: 42

Бренд: Hach Страницы: 36

Бренд: LAS Страницы: 44

Бренд: LAS Страницы: 24

Бренд: Quintex Страницы: 29

MIW-DUAL-SIGNAL-BAY

Бренд: Panamax Страницы: 2

Бренд: Smartech Страницы: 8

Бренд: Aroflora Страницы: 36

Energi Savr Node QSN-4S16-S

Бренд: Lutron Electronics Страницы: 12

Easyrack 6622520 01 01

Бренд: hepco & becker Страницы: 4

B-TRK502-02-01-SL

Бренд: SRC Страницы: 4

Бренд: La Crosse Technology Страницы: 5

Бренд: NavLinkz Страницы: 21

Бренд: J-3 International Holding Co. Страницы: 5

Бренд: 45NRTH Страницы: 2

Бренд: JANE Страницы: 58

Бренд: Imetec Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды